For those with a newer laptop, in my case a Lenovo, the NEC USBv3 port is cool, unused and so far, a pain in the ease of my mobile life.

The hardware info (from lspci -nnvv) is:

0f:00.0 USB Controller [0c03]: NEC Corporation Device [1033:0194] (rev 03) (prog-if 30)
 Subsystem: Lenovo Device [17aa:219c]
 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
 Latency: 0, Cache Line Size: 64 bytes
 Interrupt: pin A routed to IRQ 18
 Region 0: Memory at f2200000 (64-bit, non-prefetchable) [size=8K]
 Capabilities: [50] Power Management version 3
 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
 Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
 Address: 0000000000000000  Data: 0000
 Capabilities: [90] MSI-X: Enable- Count=8 Masked-
 Vector table: BAR=0 offset=00001000
 PBA: BAR=0 offset=00001080
 Capabilities: [a0] Express (v2) Endpoint, MSI 00
 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
 ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
 DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
 RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
 MaxPayload 128 bytes, MaxReadReq 512 bytes
 DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
 LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 unlimited
 ClockPM+ Surprise- LLActRep- BwNot-
 LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
 ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
 LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
 DevCap2: Completion Timeout: Not Supported, TimeoutDis+
 DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
 LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
 Compliance De-emphasis: -6dB
 LnkSta2: Current De-emphasis Level: -3.5dB
 Capabilities: [100] Advanced Error Reporting
 UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
 UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
 UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
 CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
 CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
 AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
 Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
 Capabilities: [150] #18
 Kernel driver in use: xhci_hcd
 Kernel modules: xhci-hcd



Up until the 2.6.35 kernel, this had been using the kernel driver “xhci”, but in >= 2.6.35, it has been renamed “xhci_hcd”.

What does this have to do with anything?  The ease of my suspending to disk. This USBv3 driver is not yet playing well with the freezing/thawing process, and will give a cryptic error in /var/log/pm-suspend.log, pointing you to line 295 of /usr/lib${LIBSUFFIX}/pm-utils/pm-functions. When it gets to the point of executing `echo -n "mem" > /sys/power/state`, it returns a permission denied. Even though the contents of /sys/power/state show something like “mem disk”.

So for pm-utils, if you

  • go to /etc/pm/config.d/
  • create a file called “unload_modules“, with contents of
  • SUSPEND_MODULES="xhci xhci_hcd"
  • it’s a space delimited value, so add others if you are having issues.

TA DA. now i can resume the comfort of a quick suspend and resume!

Take care,

vb Continue reading